How much does a metal driveway gate cost in Pearland?

A custom wrought iron or steel driveway gate typically runs $1,500 to $6,000 for a manual swing, and $4,000 to $12,000 once you add an operator, safety sensors, and a keypad. The metal, the span, and the ornamentation drive the range. We give a firm itemized quote after we measure.

Should I repair my old gate or replace it?

It depends on what failed. A sagging gate is often a worn hinge or a shifted post, and a service visit in the $150 to $600 range can restore it for years. When the frame is cracked through or the operator is obsolete, replacement is the better value. We tell you which on the first visit.

What is the difference between a swing gate and a slide gate?

A swing gate hinges open like a door and needs clear space behind the arc. A slide or cantilever gate rolls sideways and suits short or sloped driveways where a swing has no room. We recommend one based on your opening, not on price alone.

Which metal is best, wrought iron, steel, or aluminum?

Wrought iron and mild steel are the strongest and most ornamental but cost more and need a good finish against rust. Galvanized steel balances strength and price. Aluminum is lightweight and rust-free, a smart pick for a pedestrian or garden gate in Gulf-coast humidity.

Do I need a permit for a driveway or security gate?

Sometimes. Brazoria County and the City of Pearland may require a permit depending on the location, height, and whether the gate is automated near a right-of-way. We check the setback and clearance rules and pull the permit when it is required, and that cost is shown on your quote.

Can you automate my existing manual gate?

Often, yes. If the frame is square and the posts are solid, we can add a slide or swing operator, a control board, safety photo-eyes, and a keypad or remote. We inspect the gate first and quote the retrofit line by line, including any post reinforcement it needs.

How deep do the gate posts have to be set?

Structural posts are set in concrete footings sized to the gate weight and the local frost depth, usually well past two feet for a heavy driveway gate. A post that is too shallow is the most common reason a gate starts to sag, so we do not shortcut the footing.

What does the guarantee cover?

Every install carries a written workmanship guarantee on the fabrication and the setting of your posts. Operators, keypads, and hardware carry their own manufacturer warranties, which we hand you in writing. If a covered part fails, we come back and make it right.

Pearland Gate Installers, Swing & Slide Gates

Name: Elizabethbaron
Address: 7348 Cullen Parkway, Pearland, TX, 77581, US
Telephone: (281) 333-5451

Metal Gate Installation in Pearland, TX

Driveway gates, automatic openers, and wrought iron built to fit your opening. You get an itemized quote before any post goes in the ground, so the number you approve is the number you pay.

Call (281) 333-5451 Get a Detailed Estimate

Itemized written quotes
Swing and slide gates
Licensed and insured

Clear breakdowns of what metal gates cost in the Pearland area and where your money actually goes.

Wrought iron driveway gate in Pearland, TX

What a Metal Gate Actually Costs in Pearland

July 1, 2026

When a driveway gate quote lands in your inbox as one big number, it is hard to know whether it is fair. The truth is that a gate price is built from a handful of parts, and once you can see them, the whole thing makes sense. Here is where your money actually goes on a metal gate in the Pearland area.

The Metal Sets the Floor

The single biggest cost driver is the material. Aluminum is the lightest and cheapest and never rusts, which makes it a smart pick for a pedestrian gate. Galvanized steel costs a bit more and adds real strength. Wrought iron and mild steel sit at the top because they are heavier, stronger, and take the ornamental work most people picture when they think of a nice gate. Choose the metal first, and the rest of the quote follows.

Size and Span Do the Math

A wider opening needs more metal, longer rails, and beefier posts, so a double-swing driveway gate costs more than a single walk-through. Height adds to it too. This is why a basic steel pedestrian gate can start near $300 while a custom wrought iron driveway gate runs $1,500 to $6,000. You are paying for the span, not just the style.

The Motor Is Its Own Line

Automation is where prices climb, and for good reason. Adding an automatic gate system means an operator sized to the gate weight, a control board, safety photo-eyes, a buried loop detector, and a keypad or remotes. That package commonly pushes a full system into the $4,000 to $12,000 range. It buys you hands-free entry and built-in safety stops, but it is a real cost you should see itemized.

The Parts You Do Not See

Under every good gate are the parts that never make the photos: concrete footings poured below the frost depth, ball-bearing hinges or a V-track, latches, drop rods, and a primer-and-powder-coat finish that fights Gulf humidity. Skimping here is why a cheap gate starts to sag within a year. A footing set too shallow is the most common cause of a dragging gate we get called out to fix.

Repair Is Sometimes the Right Answer

If you already have a gate, do not assume you need a new one. A worn hinge or a shifted post is often a service call in the $150 to $600 range, not a full replacement. We will tell you honestly which one your gate needs.

Want a straight, itemized number for your property? Contact us or call Elizabethbaron at (281) 333-5451 for a detailed estimate.

Read the full article

Elizabethbaron provides metal gate installation in Pearland, TX, and the quote is where we start, not where we hide the details. Our crews handle driveway and entry gate installation, automatic and motorized gate systems, wrought iron and ornamental fabrication, security and access-control gates, and pedestrian and garden gates, plus chain-link and ranch gates when a property calls for them. Every one of those jobs gets priced the same honest way, itemized line by line, whether your home sits off Cullen Parkway or out near Shadow Creek Ranch.

A gate price is never one number pulled from the air. It is the sum of parts you can see. The metal matters most: wrought iron and mild steel cost more than aluminum, and hot-dip galvanized steel sits in between. Then come the finish, usually a rust-inhibiting primer under a powder coat, the hinges and latches, and the concrete footings that hold your posts below the local frost depth. A manual ornamental swing gate might land near $2,400, while adding a motor, a control board, safety photo-eyes, and a keypad can push a full automated system past $6,000. We show you each of those lines so you know exactly where your money goes.

Before you spend on a new gate, we tell you honestly whether a repair makes more sense. A sagging gate is often a worn hinge or a shifted post, not a lost cause, and a $300 service call can buy you several more years. When a frame is cracked through or an operator is obsolete, we say so and price the replacement instead. That repair-or-replace conversation happens on the first visit, in plain language, before any commitment. We measure the opening, check the slope and the setback, and walk you through swing versus slide based on your driveway, not on what earns us the most.

Our pricing stays honest because it is written down and it does not move after the handshake. The estimate is itemized, the change orders are rare, and the ones that happen get your signoff first. Every gate we install carries a workmanship guarantee in writing, and the operators and hardware carry their own manufacturer warranties on top of that. We are a licensed and insured local crew, we pull permits when Brazoria County requires them, and a real person answers when you call about a gate on Broadway Street or a ranch entrance out toward Manvel Road.

Itemized, not lump-sumYour quote breaks out metal, finish, hardware, footings, and any operator, so you see every dollar before you approve it.
Repair before replaceIf a hinge, latch, or post fix will save the gate, we tell you that first instead of selling a new one.
Guarantee in writingA written workmanship guarantee on the install, plus manufacturer warranties on operators and hardware.
Local and licensedA licensed, insured Pearland-area crew that pulls the required permits and answers the phone.

Gate pricing tracks three things: the metal, the size of the opening, and whether you add an operator. A basic steel pedestrian gate is the entry point, a custom wrought iron driveway gate sits in the popular middle, and a full automated system with a motor, safety sensors, and a keypad runs highest. Footings, ornamentation, and access control add to the total. The ranges below are typical for the Pearland area, and we put the firm, itemized number in writing after we measure your opening.

Steel pedestrian gate$300 to $1,200 installed	Wrought iron driveway gate$1,500 to $6,000 per job	Automated gate system$4,000 to $12,000 per job
Walk-through steel or aluminum Hinges and latch included Get estimate	Custom single or double swing Powder-coated to match your fence Get estimate	Operator, keypad, and remotes Safety photo-eyes and loop detector Get estimate

One local crew for every metal gate job, and each one priced the same clear way.

Driveway and Entry Gates
Single-swing, double-swing, and cantilever slide gates fabricated to your opening and set on structural steel posts or a gate track for smooth vehicle access.
Automatic and Motorized Systems
Slide and swing operators with control boards, keypads, remotes, safety photo-eyes, and loop detectors, wired to line power or solar for hands-free entry.
Wrought Iron and Ornamental Gates
Custom-forged pickets, scrolls, and finials welded to match your fencing and finished with a rust-inhibiting primer and powder coat that holds up in Gulf humidity.
Security and Access-Control Gates
Perimeter and pedestrian security gates tied to keypads, card readers, and video intercom entry, with safety edges for gated communities and commercial sites.
Pedestrian and Garden Gates
Walk-through steel, aluminum, and wrought iron gates for side yards and courtyards, hung on self-closing hinges with latches and drop rods.
Gate Repair and Restoration
Hinge and latch replacement, post resetting, welding of cracked frames, operator troubleshooting, and refinishing of corroded ironwork, priced by the visit.

How much does a metal driveway gate cost in Pearland?: A custom wrought iron or steel driveway gate typically runs $1,500 to $6,000 for a manual swing, and $4,000 to $12,000 once you add an operator, safety sensors, and a keypad. The metal, the span, and the ornamentation drive the range. We give a firm itemized quote after we measure.
Should I repair my old gate or replace it?: It depends on what failed. A sagging gate is often a worn hinge or a shifted post, and a service visit in the $150 to $600 range can restore it for years. When the frame is cracked through or the operator is obsolete, replacement is the better value. We tell you which on the first visit.
What is the difference between a swing gate and a slide gate?: A swing gate hinges open like a door and needs clear space behind the arc. A slide or cantilever gate rolls sideways and suits short or sloped driveways where a swing has no room. We recommend one based on your opening, not on price alone.
Which metal is best, wrought iron, steel, or aluminum?: Wrought iron and mild steel are the strongest and most ornamental but cost more and need a good finish against rust. Galvanized steel balances strength and price. Aluminum is lightweight and rust-free, a smart pick for a pedestrian or garden gate in Gulf-coast humidity.
Do I need a permit for a driveway or security gate?: Sometimes. Brazoria County and the City of Pearland may require a permit depending on the location, height, and whether the gate is automated near a right-of-way. We check the setback and clearance rules and pull the permit when it is required, and that cost is shown on your quote.
Can you automate my existing manual gate?: Often, yes. If the frame is square and the posts are solid, we can add a slide or swing operator, a control board, safety photo-eyes, and a keypad or remote. We inspect the gate first and quote the retrofit line by line, including any post reinforcement it needs.
How deep do the gate posts have to be set?: Structural posts are set in concrete footings sized to the gate weight and the local frost depth, usually well past two feet for a heavy driveway gate. A post that is too shallow is the most common reason a gate starts to sag, so we do not shortcut the footing.
What does the guarantee cover?: Every install carries a written workmanship guarantee on the fabrication and the setting of your posts. Operators, keypads, and hardware carry their own manufacturer warranties, which we hand you in writing. If a covered part fails, we come back and make it right.

We install and service metal gates across Pearland and the surrounding Brazoria County communities, from the Shadow Creek Ranch and Silverlake neighborhoods to the nearby towns south and west of Houston.

Not sure if we reach your street? Call (281) 333-5451 and we will tell you straight.

Pearland, TX (77581, 77584)
Friendswood, TX
Manvel, TX
Alvin, TX
League City, TX
Missouri City, TX
Iowa Colony, TX

Ready for a gate that fits your opening and a price with nothing buried in it? We will measure your driveway, check the slope and setback, walk you through swing versus slide and manual versus automated, and hand you an itemized written estimate. No pressure, no lump-sum guessing, just a clear number for the gate you actually want.

Call (281) 333-5451

Metal Gates for Pearland Homes, Priced Straight

Gate Buying Tips

What a Metal Gate Actually Costs in Pearland

The Metal Sets the Floor

Size and Span Do the Math

The Motor Is Its Own Line

The Parts You Do Not See

Repair Is Sometimes the Right Answer

What Metal Gate Installation Costs in Pearland

The Gate Services Behind Every Quote

Driveway and Entry Gates

Automatic and Motorized Systems

Wrought Iron and Ornamental Gates

Security and Access-Control Gates

Pedestrian and Garden Gates

Gate Repair and Restoration

Cost Questions, Answered Plainly

Towns and ZIP Codes We Serve

Get Your Detailed Gate Estimate